空氣彈簧說明書
溫度
標準用空氣彈簧的使用溫度范圍為: -40C~ +60°C
壓力
1.標準型空氣彈簧根據我們的經驗:最大使用壓力為0.7 Mpa。
2.高強度(四層骨架層)空氣彈簧最大壓力1.25Mpa。
我們推薦在較大內部空氣壓力和破裂壓力之間有2.5倍的安全系數，所以，舉個例子說，如果需要0.7Mpa的壓力，破裂壓力應是1.75Mpa或更大。曲囊形空氣彈簧的破裂壓力隨高度增加而減小。因此，決定因素有兩個方面，伸長最大高度，以及在這一點上的內壓是多少?壓力與高度的函數關系請參考充氣壓力圖。
空氣彈簧儲運須知
1.運輸、裝卸過程禁止粗暴作業。
2.存放于干燥通風的庫房?jī)?nèi),避免日光直曬。
3.安裝部位應有足夠的安裝空間，避免和油類、酸堿類物質及堅銳物質接觸。
4.避免用堅銳工具觸碰空氣彈簀;與其配合的配套件應光滑無棱角。
注意事項：
空氣彈簧氣囊總成未與懸架安裝固定之前請勿充氣，否則會使氣囊和底座分離造成沒有必要的損失。
temperature
The temperature range for standard air springs is -40 ° C to+60 ° C
pressure
1. According to our experience, the maximum operating pressure for standard air springs is 0.7 Mpa.
2. High strength (four layer skeleton layer) air spring with a maximum pressure of 1.25 Mpa.
We recommend a safety factor of 2.5 times between the larger internal air pressure and the rupture pressure. Therefore, for example, if a pressure of 0.7 Mpa is required, the rupture pressure should be 1.75 Mpa or higher. The rupture pressure of the curved air spring decreases with increasing height. Therefore, there are two determining factors, the maximum height of elongation, and what is the internal pressure at this point? Please refer to the inflation pressure chart for the function relationship between pressure and height.
Air Spring Storage and Transportation Notice
1. Rough operations are prohibited during transportation and loading and unloading.
2. Store in a dry and ventilated warehouse, avoiding direct sunlight.
3. The installation site should have sufficient installation space to avoid contact with oil, acidic or alkaline substances, and sharp substances.
4. Avoid using sharp tools to touch air bombs; The matching parts should be smooth and free of edges and corners.
Notes:
Do not inflate the airbag before it is fixed to the suspension, otherwise it will separate the airbag from the base and cause unnecessary damage.